partial replacement of sand by copper slag

  • A Review on Partial Substitution of Copper Slag with Sand

    copper slag as a partial substitute of Sand (up to 40%) in concrete but in terms of stability the concrete found to be low resistant to acid attack and better resistance

    • Author: Paresh Tiwari, Anil Kumar Saxena

  • [PDF] The Behaviour of Concrete by Partial Replacement of

    In this study, partial replacement of Cement with GGBS and Sand with Copper Slag considered. Experimental study is conducted to evaluate the workability and strength characteristics of hardened concrete, properties of concrete have been assessed by partially replacing cement with GGBS, and sand with Copper Slag.

  • Utilization of Copper Slag in M-Sand as Partial

    chemical properties of Sand. Copper slag is considered as a waste material which could be used in the construction industry as partial substitute of either cement or aggregates. The use of copper slag in concrete provides potential environmental as well as economic benefits to the construction industry.

  • Partial Replacement Of Sand By Copper Slag Henan FUMINE

    Partial replacement of sand by Copper Slag in concrete is allowed up to 10 by mass. Copper Slag has similar properties to sand and is a very effective substitute during monsoon rainy season. Further Copper Slag is also used in the production of cement mortar and concrete as a raw material for clinker cement replacement coarse and fine

  • Performance of Copper slag and ferrous slag as partial

    copper slag can be used as a partial replacement for sand as fine aggregate in concrete up to 40% in pavement grade concrete with out any loss of cohesiveness and the compressive and flexural strength of such concretes is about 20% higher than that of

  • A STUDY ON THE PROPERTIES OF CONCRETE ON PARTIAL

    In the present experimental work, copper slag are used as partial replacement for cement and sand in the concrete mix. 3.1 Cement: Cement,in general, adhesive substances of all kinds, but, in a narrower sense, the binding materials used in building and civil engineering construction. Cements of

  • Copper slag as sand replacement for high performance

    Aug 01, 2009· It is recommended that 40 wt% of copper slag can be used as replacement of sand in order to obtain HPC with good properties. 6. It should be noted that further research work is needed to explore the effect of copper slag as fine aggregates on the properties of concrete with different cement types, silica fume sources and the degree of fines.

    • Cited by: 233

  • Partial Replacement of Copper Slag as Fine Aggregate

    copper slag. Fig.7. Comparison of Flexural Strength of Beam IV. CONCLUSION The concrete was prepared for the M 25 grade concrete with partial replacement of fine aggregate by copper slag with various percentages of 0%, 10%, 15% and 20%. The specimens were casted for 7days, 14 days and 28 days then tested. The results are presented above.

  • Study of Strength Properties of Concrete by Partial

    Copper slag which is an industrial waste product can be used as replacement for cement with sand and contributes to the increase in various mechanical properties of concrete. Copper slag can be used up to 30% but when used ahead of 50% results in decrease in strengths.

  • Comparison of The Replacement of Natural Sand by Copper

    The recommended percentage replacement of sand by copper slag is 40% but when used beyond 50% results in decrease in strengths.Daniel C, Joel Shelton J etal studied on Investigation on strength properties of self compacting concrete with copper slag as

  • partial replacement of sand with steel slag

    partial replacement of sand by steel slag in concrete. Slag Admixed Concrete corrosion and durability tests on concrete contai ning copper slag as partial replacement of sand and cement For this research work, M20 grade concrete was used and the tests, cementitious properties of different slags like blast furn ace slag, steel slag, copper slag and phosphorous slag, sand an d cement replacement

  • Study of Strength Properties of Concrete by Partial

    “Study of Strength Properties of Concrete by Partial Replacement with Fly Ash and Copper Slag in Cement And Fine Aggregate” G Swathi1, G Dinesh 2 1 Assistant Professor, Civil Engineering Department, Aditya Engineering College, Surampalem, AP. 2Assistant Professor, Civil Engineering Department, Aditya Engineering College, Surampalem, AP. Abstract- For every ton of resCopper slag

  • Studies on use of Copper Slag as Replacement Material for

    Aug 20, 2014· The percentage of copper slag used for replacement of river sand are 0, 25, 50 and 75 %. Cement sand mortar joint thickness of 10 and 15 mm. Plaster ability of use of copper slag for partial replacement material for river sand. Use of copper slag as replacement material for river sand in cement concrete (0, 25, 50, 75 and 100 %)

  • Partial Replacement of Copper Slag as Fine Aggregate

    copper slag. Fig.7. Comparison of Flexural Strength of Beam IV. CONCLUSION The concrete was prepared for the M 25 grade concrete with partial replacement of fine aggregate by copper slag with various percentages of 0%, 10%, 15% and 20%. The specimens were casted for 7days, 14 days and 28 days then tested. The results are presented above.

  • Copper Slag Sand Replacement

    Performance of copper slag and ferrous slag as partial.copper slag can be used as a partial replacement for sand as fine aggregate in concrete up to 40 in pavement grade concrete with out any loss of cohesiveness and the compressive and flexural strength of such concretes is about 20 higher than that of conventional cement.details.

  • the replacement of granulated copper slag for sand concrete

    Performance of Copper slag and ferrous slag as partial . copper slag can be used as a partial replacement for sand as fine aggregate in concrete up to 40% in pavement grade concrete with out any loss of cohesiveness and the compressive and flexural strength of such concretes is about 20% higher than that of conventional cement concretes of the same grade

  • Partial Replacement Of Fine Aggregate By Slag Sand

    Copper Slag Used As A Fine Aggregate Pdf. D replacement of fine aggregate with copper slag the effect of the partial replacement of sand by slag on mortar and concrete properties is investigated two different sands and four different volume contents of copper slag 20

  • A CASE STUDY ON COPPER SLAG AS PARTIAL

    strength properties of copper slag as a partial replacement of sand at different levels (0%, 20% and 40%). Copper slag is a by-product obtained during the matte smelting and refining of copper. In the present investigation it is proposed to study the engineering properties of Copper slag viz. Slump test,

  • River Sand with Crush Sand and Copper Slag Study of

    foundry sand for replacement of fines in concrete and found that at 20-20 % replacement of copper slag and foundry sand in concrete gives highest compressive strength. Praveen kumar k[5], 2015: found that workability of mortar increases with partial replacements up to 80% and reduces upon complete replacement. For 1:6 cement mortar using

  • Effects of Copper Slag as Sand Replacement in Concrete

    The specific gravity of sand and copper slag was 2.67 & 2.75 respectively as shown in Table 2.1. The water absorption of 20 mm coarse aggregates, sand &copper slag was found to be 0.609, 1.01 and 0.65 respectively. It was found that water absorption of copper slag was very low as compared with the natural sand and workability of concrete is

  • Partial Replacement of Copper Slag as Fine Aggregate

    Finally, mathematical equations were derived for compressive strength at 28 & 90 days with percentage of Copper Slag used as partial replacement of Fine aggregate in copper slag admixed concrete.

  • Partial replacement of Fine aggreggate by Copper Slag and

    Jan 16, 2017· The percentage replacement of sand by granulated copper slag where 0%, 5%, 10%, 15%, 20%, 30%, 40% and 50%. The compressive strength was observed to increase by about 35-40% and split tensile strength by 30-35%. The experimental investigation showed that percentage replacement of sand by copper slag shall be up to 40%. 11.

  • Partial Replacement Of Copper Slag In Fine Aggregate

    Mixes with copper slag gave concrete with adequate properties, with the optimal sand replacements by water-cooled copper slag overall being in the region of 30-60.Based on the results water-cooled copper slag can be considered to be a suitable candidate for the partial replacement of fine aggregate in concrete.This shows promise for.

  • copper slag as sand replacement on hpc

    replacement of fine aggregate with copper slag for . copper slag as sand replacement on hpc. using copper slag as a replacement of fine aggregate on the strength properti M25 grade concrete was used and tests were conducted for various proportions of copper slag replacement with sand of 0 to in concrete The test results indicate that compressive strength of concrete Chat Online copper slag mill

  • Partial Replacement Of Copper Slag In Fine Aggregate

    Mixes with copper slag gave concrete with adequate properties, with the optimal sand replacements by water-cooled copper slag overall being in the region of 30-60.Based on the results water-cooled copper slag can be considered to be a suitable candidate for the partial replacement of fine aggregate in concrete.This shows promise for.

  • A Study on Concrete Mix Design of Partial and Full

    Jan 24, 2019· Many researchers have already found it possible to use Copper slag as a concrete aggregate, because copper slag has similar particle size characteristics likely to that of sand. Hence the study focuses on the various percentage replacement of Copper Slag with Fine aggregate varying from 38% to 52% at interval of 2%, since replacement of 40% to

  • project reports on slag sand wehelpenkampen.nl

    Use of Iron Slag as Partial Replacement of Sand to. 20% and 30% iron slag with the sand. On the basis of recent testing, subsequent conclusions were drawn. After adding 10% iron slag in the mix, there was an increase of 26% after 7 days, 50% increase after 28 days and 43% increase after 56 days as compared to the control mix.

  • A CASE STUDY ON COPPER SLAG AS PARTIAL

    strength properties of copper slag as a partial replacement of sand at different levels (0%, 20% and 40%). Copper slag is a by-product obtained during the matte smelting and refining of copper. In the present investigation it is proposed to study the engineering properties of Copper slag viz. Slump test,

  • Copper Slag Sand Replacement

    Performance of copper slag and ferrous slag as partial.copper slag can be used as a partial replacement for sand as fine aggregate in concrete up to 40 in pavement grade concrete with out any loss of cohesiveness and the compressive and flexural strength of such concretes is about 20 higher than that of conventional cement.details.

  • Partial Replacement Of Fine Aggregate By Slag Sand

    Copper Slag Used As A Fine Aggregate Pdf. D replacement of fine aggregate with copper slag the effect of the partial replacement of sand by slag on mortar and concrete properties is investigated two different sands and four different volume contents of copper slag 20

  • Copper slag Wikipedia

    Copper slag can be used in concrete production as a partial replacement for sand. Copper slag is used as a building material,formed into blocks. Such use was common in areas where smelting was done, including St Helens and Cornwall [2] in England .

  • EXPERIMENTAL STUDY OF CONCRETE WITH COPPER SLAG

    The percentage of copper slag used for replacement of river sand are 0%, 10%, 20%, 30%, 40%, 50%. Cement sand mortar joint thickness of 10 and 15mm. Plaster ability of use of copper slag for partial replacement material for river sand. Use of copper slag as replacement material for river sand in cement concrete.

  • fly ash as replacement of sand

    class c fly ash as a full or partial replacement for . were used to evaluate the performance of the sand specimens (i.e., sand plus fly ash alone, sand plus fly ash and lime, sand plus fly ash and cement, and sand plus cement alone). this specification required the minimum cement content to cor­ respond to a strength of 250 psi with a 7 day curing period at a temperature of 73° ± 3° f.

  • PARTIAL REPLACEMENT OF CEMENT WITH GGBS AND

    Experimental investigation conducted by complete replacement of slag with cement and partial replacement of slag and mineral admixtures by weight in the form of 3cubes by using M30 grade. that by the partial replacement of cement with GGBS and sand with ROBO SAND. III. Ground granulated blast furnace slag (GGBS) copper slag, and silica

  • Effects of Copper Slag as Sand Replacement in Concrete

    The specific gravity of sand and copper slag was 2.67 & 2.75 respectively as shown in Table 2.1. The water absorption of 20 mm coarse aggregates, sand &copper slag was found to be 0.609, 1.01 and 0.65 respectively. It was found that water absorption of copper slag was very low as compared with the natural sand and workability of concrete is

  • CIVIL EXPERIMENTAL PROJECTS Majestic Project

    Experimental Investigation on Partial Replacement of Fine Aggregate with Copper Slag CEX011. Experimental Analysis of Component Interaction in Concrete Effect of High Performance Concrete in PCC Structure by Partial Replacement of Agricultural Waste Experimental Investigation on Partial Replacement of Cement by Fly Ash and Sand by

  • River Sand with Crush Sand and Copper Slag Study of

    foundry sand for replacement of fines in concrete and found that at 20-20 % replacement of copper slag and foundry sand in concrete gives highest compressive strength. Praveen kumar k[5], 2015: found that workability of mortar increases with partial replacements up to 80% and reduces upon complete replacement. For 1:6 cement mortar using

  • Study on Mechanical Properties of Concreteon Partial

    copper slag and granite powder can be used as a partial replacement of sand. Granite stone powder, a by-product from the cutting process of granite stone used for flooring is one of such materials. Copper slag is a by-product obtained during the matte smelting and refining of copper.